neoVI RED 2 Specifications

Overview

Specifications

neoVI RED 2 Specification

Protocol Support

  • OBD
  • J1939: Includes J1939 DBC, BAM, RTS/CTS
  • UDS (ISO14229):
    1. Services include $19, $22, $23, $2A, $2C
    2. DBC, A2L (ASAP2 File), GDX, MDX, ODX support
  • CCP: Includes A2L (ASAP2 file) and ROB support
  • XCP: Includes A2L (ASAP2 file) and ROB support

Networks / Inputs

  • 2, 4, or 8 x Dual wire CAN (all baud rates supported)
  • 2 LIN / K Line / KW2K / ISO 9141
  • 2 Gigabit Ethernet (1000BASE-T)

Device Specifications

  • Low power consumption
  • Comatose: 500 microamps
  • Fast wake 70 milliamps
  • Power supply: 5-60V operation
  • LEDs: 10 programmable tri-color LEDs
  • 2 LEDs for legacy status; 2 user buttons
  • Temperature range: -40°C to +85°C
  • On-board UPS power supply for safe shutdown of data logger
  • Dimensions: 13.60cm by 11.22cm by 3.97cm
  • LEDs (user programmable): 10 programmable tri-color LEDs
  • SD card: 2 card slot support for up to 2 TB of storage; card
  • formatted using FAT32 for PC compatibility
  • DAQ Ethernet
  • Vehicle connectors: 26-pin male HD D-sub
  • One-year limited warranty
  • Field-upgradeable flash firmware
  • General purpose I/O: 4 MISC IO (0-40V); can be configured as analog/ PWMIO
  • General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change
  • USB host for RAD-IO2 or neoVI MIC2
  • Standalone mode, including scripting, receive messages, transmit messages, expressions, I/O and transport layers
  • J2534 and RP1210 A/B compatible for CAN / ISO15765- 2:2016 (CAN FD)
  • Battery-backed real-time clock (RTC)

Timing Specifications

  • 64-bit timestamping to an accuracy of 25 nanoseconds on all networks
  • Simultaneous operation on all CAN/LIN networks
  • Transmit message double-buffering on all networks, allowing back-to-back message transmission

Network Specifications – CAN

  • 2, 4 or 8 x ISO CAN FD channels
  • CAN 2.0B compatible for all CAN networks
  • 2-8 dedicated ISO11898 Dual Wire CAN FD physical layers (TJA1043)
  • Up to 1 Mb/s software-selectable baud rate for arbitration phase (auto baud capable)
  • Up to 8 Mb/s software-selectable baud rate for data phase (auto baud capable)
  • Listen-only mode support

Network Specifications – LIN / K Line / KW2K / ISO 9141 Up to 2x LIN (Local Interconnect Network)

  • Full support for LIN 1.X, 2.X and J2602
  • LIN J2602 / 2.X compatible physical layer
  • Software-enabled 1K LIN Master Resistor per channel
  • LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/ Slave Not Responding, Checksum Error and Transmit Bit Errors
  • LIN Bus Master Mode operates at same time as LIN Bus Monitor
  • LIN Bus Slave simulation, with or without an LDF file
  • LIN Bus hardware schedule table with support for LIN diagnostics
  • Initialization Waveforms, including Fast Init, Five Baud, and Custom
  • Software-selectable baud rate

Ordering Information

Part Number

Description

NEOVI-RED2-2

neoVI RED 2 with Vehicle Spy Trial – 2 CAN/CAN FD channel with two software enable CAN termination

NEOVI-RED2-4

neoVI RED 2 with Vehicle Spy Trial – 4 CAN/CAN FD channel with four software enable CAN termination

NEOVI-RED2-8

neoVI RED 2 with Vehicle Spy Trial – 8 CAN/CAN FD channel with four software enable CAN termination

Specifications subject to change; please contact Intrepid for the latest information. All trademarks are the property of their respective owners

JapanKoreaChinaUSA